Followers

Monday, January 18, 2016

Challenge #3 - Let's Make A Box

Hello, Crafty Peeps!

Surprise!  Not exactly the kind of box you were expecting!  Well the basics are pretty much the same.  I thought I would share a tutorial I did a while back.  These little note boxes are super easy (although my tut might seem very involved) and will provide a great learning foundation for future box projects.



 These are fun and easy to make so let's get started!

Step One:  Gather Your Materials
2- 12 x 12 sheet of heavyweight chipboard
1- roll of clear shelf liner (this is optional)
1- 12"x 12" sheet of designer paper
1-3 sheets of 6x6 designer paper
 (depends on your design)
Scor-tape, Scor-board, Craft Knife
Paper Cutter, Ruler

Step 2 - Cut your chipboard
Cut the Chipboard:  (2) 4-1/2"x 5-1/2" pieces  and (1) 1"x5-1/2"Piece


Step 3 - Designer Paper

Cut your Designer Paper to 12"x7".  Cut a piece of the shelf liner that is slightly larger than your dp.  I usually have a 1/4" overlap.  Starting in one corner apply the shelf liner.  Use your bone folder to smooth and to prevent air bubbles. Trim excess liner. Set aside.
Step 4 - Adhere Chipboard
Add Scor-tape to one side of the chipboard pieces

Arrange the pieces on the back of your cover so that there is a 1/8" gap.  Place a ruler at the bottom to keep pieces straight and to find center.  Remove tape. Place pieces one a a time.

 Cut your corners as shown above.
Apply Scor-Tape to chipboard (or paper. Your choice)

Run your bone folder along the edges and start to bend by lifting up your cover.  Remove tape and seal.  Burnish with bone folder.

Step 5 - Finish Inside
Cut one piece of dp large enough to finish one side of your base and and center spine. Adhere.


Cut a second piece large enough to cover the other side and half of the spine.  Cut the ends that will attach to the spine at an angle.  This is the Top of your note box. 

Use your bone folder to true all your folds.
Your base is now complete.

Step 6 - Create Your Paper Tray
 Cut a piece of Heavyweight Card Stock/Designer Paper to 7"x6" and score at 1" on all sides.
Cut the interior score line on each corner. Add tape and form box.
Adhere a 1" piece of Scor-tape to the back of the box
 Adhere Scor-tape to the bottom of the box
 Center the paper tray on the bottom base. Remove the tape at the bottom of the paper tray first.  Make sure that the tray is flush.  Finally remove the tape at the back of the tray adhere to spine by pressing the spine against the tray.  The angle cut will make sure the tray closes automatically.  If you want a thumb cut in your paper tray. Make it before attaching the tray or applying decorative papers.


I used my Fiskars postage stamp punch to cut out my Inky Impressions "Love" Sentiment.  I added a note stamp to the bottom.
The punched piece was sponged with Iced Spruce and Evergreen Baugh D.I. 
I wrapped a 1/4" piece of black gingham ribbon, matted it on corresponding green paper 
and added a small key from my stash.
I made a banner cut on the end of the Ribbon and added my hearts.
Add note paper.  I used papers that correspond to the colors in my dp.

Here is another note box. 
The rose actually hides a magnet and serves as a clasp for the note case
 I used two designer papers and one solid card stock in this design
The possibilities are endless!

Can't wait to see yours!
Hugz,
Chana Malkah

No comments:

Post a Comment

Thanks for visiting! We look forward to seeing your submissions to our challenge. Your support of our little challenge is greatly appreciated!

Hugz,
Chana